Latest Shipping Policy to US
Due to recent changes in U.S. tariff policies, US customers are responsible for any applicable import duties on their orders shipping from China Warehouse. Please be aware of this before placing your order.
1 5
Speedybee  |  SKU: NA0357

SpeedyBee F405 Mini Flight Stack with BLS 35A 4-in-1 ESC 20x20

$69.99

US Shipping Notice

Due to the new tarrif policy, if you choose the following shipping method to US:
Express Shipping: Plese provide your Fedex Account.
DHL: Please provide your EIN or SSN number.
Tarrif bill will send to these account.

The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4-level battery voltage display and a built-in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
The 35A 4-in-1 BLHeli_S Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via a 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.

Features:
1.TVS transient suppression diode for surge voltage absorption and enhanced protection
2.Compatibility with 2-4 inch and lightweight 5-inch quadcopters
3.Four synchronized outputs with a continuous current of 35A
4.Dual BEC setup: 5V 2A output and 9V 3A output
5.Built-in Bluetooth chip for wireless Betaflight tuning
6.Supports connectivity to all DJI Air Units
7.Upgraded F405 flight controller chip
8.4-level battery voltage display
9.35A continuous current output
10.Supports 4-6S battery
11.4 available UART ports
12.Built-in barometer

Specifications:

SPEEDYBEE F405 V3 20X20 FLIGHT CONTROLLER

DJI Air Unit Compatibility: Compatible with all DJI Air Units (DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1). Use specific solder pads for pin-to-pin connection. Note: UART1 is used for OSD and SUBS(R2) is used for SBUS receiver signal input
BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Note: MSP switch on UART 4 must be turned on and set to a baud rate of 115200 for Bluetooth functionality
Wireless FC Firmware Flashing: NOT Supported. Connect to Betaflight configurator on PC for firmware update
Wireless Blackbox Download & Analysis: NOT Supported. Connect to Betaflight configurator on PC for blackbox analysis
Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, set Scale=250 and Offset=-500
Power Input: 3-6S LiPo. Powered through 8pin harness G, V wires or G, V pads from bottom side
BOOT Button: Supported. Forces FC to enter DFU mode for firmware flashing
3.3V Output: Supported. Designed for 3.3V input receivers. Up to 500mA current load
4.5V Output: Supported. Designed for radio receiver and GPS module. Up to 1A current load
Mounting: 20 x 20mm, 3.5mm hole diameter. Compatible with M2 and M3 screws/Silicone grommets
I2C: Supported. DA & CL pads on the front side for magnetometer, sonar, etc
Traditional Betaflight LED Pad: Supported. Used for WS2812 LEDs
Supported Flight Controller Firmware: BetaFlight (Default), INAV
BetaFlight Camera Control Pad: Yes. CC pad on the front side
ESC Signal: M1 - M4 wires or soldering pads on the bottom side
UART: 6 sets. UART1-6 with dedicated purposes
Firmware Target Name: SPEEDYBEEF405MINI
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
5V Output: 4 groups. The total current load is 2A
9V Output: 1 group. The total current load is 3A
DJI Air Unit Connection Way: Direct soldering
Dimension: 30(L) x 32(W) x 7.8(H)mm
Smart Port / F.Port: Not Supported
ESC Telemetry: UART R5 (UART5)
Blackbox: 8MB Onboard Flash
RSSI Input: Not Supported
OSD Chip: AT7456E chip
IMU(Gyro): ICM42688P
USB Port Type: Type-C.
WIFI: Not supported
Barometer: Built-in
MCU: STM32F405
Weight: 9.6g

SPEEDYBEE 35A BLHELI_s MINI V2 4-IN-1 ESC

Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets
Power Output: VBAT (Battery voltage, used to power the flight controller)
Current Sensor: Support (Scale=250 Offset=-500)
ESC Telemetry: Not supported
Burst Current: 45A (5 seconds)
Dimension: 35 * 35 * 5.5mm
ESC Protocol: DSHOT300/600
Continuous Current: 35A * 4
Firmware: BLHeli_S J-H-40
Power Input: 3-6S LiPo
Weight: 7.2g

Package Includes:
1x SpeedyBee F405 V3 20x20 Flight Controller
1x SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
5x M2 Silicone O-Ring
5x M5 Silicone O-Ring
5x M2 Anti Vibration Silicone Grommets
5x M3 Anti Vibration Silicone Grommets
1x 8-Pin JST cable 30mm
1x 35V 470uf Capacitor
Speedybee

SpeedyBee F405 Mini Flight Stack with BLS 35A 4-in-1 ESC 20x20

$69.99
The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4-level battery voltage display and a built-in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
The 35A 4-in-1 BLHeli_S Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via a 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.

Features:
1.TVS transient suppression diode for surge voltage absorption and enhanced protection
2.Compatibility with 2-4 inch and lightweight 5-inch quadcopters
3.Four synchronized outputs with a continuous current of 35A
4.Dual BEC setup: 5V 2A output and 9V 3A output
5.Built-in Bluetooth chip for wireless Betaflight tuning
6.Supports connectivity to all DJI Air Units
7.Upgraded F405 flight controller chip
8.4-level battery voltage display
9.35A continuous current output
10.Supports 4-6S battery
11.4 available UART ports
12.Built-in barometer

Specifications:

SPEEDYBEE F405 V3 20X20 FLIGHT CONTROLLER

DJI Air Unit Compatibility: Compatible with all DJI Air Units (DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1). Use specific solder pads for pin-to-pin connection. Note: UART1 is used for OSD and SUBS(R2) is used for SBUS receiver signal input
BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Note: MSP switch on UART 4 must be turned on and set to a baud rate of 115200 for Bluetooth functionality
Wireless FC Firmware Flashing: NOT Supported. Connect to Betaflight configurator on PC for firmware update
Wireless Blackbox Download & Analysis: NOT Supported. Connect to Betaflight configurator on PC for blackbox analysis
Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, set Scale=250 and Offset=-500
Power Input: 3-6S LiPo. Powered through 8pin harness G, V wires or G, V pads from bottom side
BOOT Button: Supported. Forces FC to enter DFU mode for firmware flashing
3.3V Output: Supported. Designed for 3.3V input receivers. Up to 500mA current load
4.5V Output: Supported. Designed for radio receiver and GPS module. Up to 1A current load
Mounting: 20 x 20mm, 3.5mm hole diameter. Compatible with M2 and M3 screws/Silicone grommets
I2C: Supported. DA & CL pads on the front side for magnetometer, sonar, etc
Traditional Betaflight LED Pad: Supported. Used for WS2812 LEDs
Supported Flight Controller Firmware: BetaFlight (Default), INAV
BetaFlight Camera Control Pad: Yes. CC pad on the front side
ESC Signal: M1 - M4 wires or soldering pads on the bottom side
UART: 6 sets. UART1-6 with dedicated purposes
Firmware Target Name: SPEEDYBEEF405MINI
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
5V Output: 4 groups. The total current load is 2A
9V Output: 1 group. The total current load is 3A
DJI Air Unit Connection Way: Direct soldering
Dimension: 30(L) x 32(W) x 7.8(H)mm
Smart Port / F.Port: Not Supported
ESC Telemetry: UART R5 (UART5)
Blackbox: 8MB Onboard Flash
RSSI Input: Not Supported
OSD Chip: AT7456E chip
IMU(Gyro): ICM42688P
USB Port Type: Type-C.
WIFI: Not supported
Barometer: Built-in
MCU: STM32F405
Weight: 9.6g

SPEEDYBEE 35A BLHELI_s MINI V2 4-IN-1 ESC

Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets
Power Output: VBAT (Battery voltage, used to power the flight controller)
Current Sensor: Support (Scale=250 Offset=-500)
ESC Telemetry: Not supported
Burst Current: 45A (5 seconds)
Dimension: 35 * 35 * 5.5mm
ESC Protocol: DSHOT300/600
Continuous Current: 35A * 4
Firmware: BLHeli_S J-H-40
Power Input: 3-6S LiPo
Weight: 7.2g

Package Includes:
1x SpeedyBee F405 V3 20x20 Flight Controller
1x SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
5x M2 Silicone O-Ring
5x M5 Silicone O-Ring
5x M2 Anti Vibration Silicone Grommets
5x M3 Anti Vibration Silicone Grommets
1x 8-Pin JST cable 30mm
1x 35V 470uf Capacitor
View product

  • Customer Service

    Online Chat & Email

  • Worldwide Shipping

    DHL/Fedex/UPS...

  • Professional

    15 Years+ RC Experience

  • Secure Payment

    Paypal Payment Accept
Back to top